Tumbling dies?
-
- Posts: 15
- Joined: 27 Dec 2014 11:43
- My Press Choice: Turret
- Location: tn
- Has thanked: 7 times
- Been thanked: 7 times
Tumbling dies?
Has anyone tried tumbling dies (In particular,the die bodies) as a method of cleaning?
A bit of background...
I purchased a set of RCBS carbide dies in 38/357 for cheap but the bodies are a bit rusty. When I got them I soaked them down in WD-40, wiped them down, then oiled with a light oil. I broke them down today for a more thorough cleaning and the idea occurred to me if tossing them in my vibratory tumbler with crushed walnut for a few hours would help with the rust in the knurled areas. The bodies appear to be steel so I doubt the walnut would affect the threads or internal dimensions. I also have corncob media I could use if needed.
Has anyone else tried this? If so, what were your results? Thank you in advance.
David
A bit of background...
I purchased a set of RCBS carbide dies in 38/357 for cheap but the bodies are a bit rusty. When I got them I soaked them down in WD-40, wiped them down, then oiled with a light oil. I broke them down today for a more thorough cleaning and the idea occurred to me if tossing them in my vibratory tumbler with crushed walnut for a few hours would help with the rust in the knurled areas. The bodies appear to be steel so I doubt the walnut would affect the threads or internal dimensions. I also have corncob media I could use if needed.
Has anyone else tried this? If so, what were your results? Thank you in advance.
David
-
- Founding Member
- Posts: 736
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: Kingsland, GA
- Has thanked: 51 times
- Been thanked: 222 times
Re: Tumbling dies?
I did and it beat up my bowl. I think it might have worked with a heavier duty model like an actual parts cleaner but my cheap Frankford Arsenal model just got beat up.
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: Tumbling dies?
A wet tumbler should be able to stand the beating. They're originally made for tumbling rocks .
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- daboone
- Founding Member
- Posts: 1397
- Joined: 30 Nov 2013 21:47
- My Press Choice: Single Stage
- Location: AZ, TX, HI
- Has thanked: 677 times
- Been thanked: 787 times
Re: Tumbling dies?
I haven't tried using a buzz bucket for dies. I have used steel wool and those green scrubbing pads and a product called Bar Keepers Friend, a Comet type cleaning scrubbing powder. The carbide ring won't rust so it should be only the die body and it's internals that would be affected. You might use a small rod and steel wool for the inside of the die. I use a product call EEZOX to prevent rusting. It's worked very well for the 4 years I've used it, but then again I live in Arizona and so humidity is very low here.
An ignorant person is one who doesn't know what you have just found out.
When setting a job up for myself it must be Idiot Proof as well, as I am a bigger idiot than most people I know, and I prove it to myself everyday.
When setting a job up for myself it must be Idiot Proof as well, as I am a bigger idiot than most people I know, and I prove it to myself everyday.
- mr surveyor
- Founding Member
- Posts: 650
- Joined: 30 Jun 2013 09:30
- My Press Choice: Hand Press
- Location: NE Texas
- Has thanked: 386 times
- Been thanked: 231 times
Re: Tumbling dies?
Whatever happened to the old pink jell stuff ... Naval Jelly (?). I remember using that stuff in pretty large volumes back in the 70's to de-rust pipe, tank steel, angle iron and other "well seasoned" iron/steel building materials we used on the farm. We only used it on things we wanted to have a nice looking paint job on, and I seem to remember it would take the rust off in very short time .... you just needed to prep it pretty quick with a paint thinner wash followed by a primer coat.
jd
jd
--------------------------------------------------------------------------------------
There's just some things best left unsaid on the internetsuperhighway.
There's just some things best left unsaid on the internetsuperhighway.
- akuser47
- Moderator & Supporter
- Posts: 1397
- Joined: 30 Jun 2013 09:16
- My Press Choice: Single Stage
- Location: ohio
- Has thanked: 666 times
- Been thanked: 266 times
- akuser47
- Moderator & Supporter
- Posts: 1397
- Joined: 30 Jun 2013 09:16
- My Press Choice: Single Stage
- Location: ohio
- Has thanked: 666 times
- Been thanked: 266 times
Re: Tumbling dies?
It's small container but will definitely serve well in this case as long as you don't use it on any aluminum.
- RBHarter
- Founding Member
- Posts: 2047
- Joined: 13 Mar 2014 19:45
- My Press Choice: Single Stage
- Location: The green hell 90 miles north of Texarka
- Has thanked: 76 times
- Been thanked: 672 times
Re: Tumbling dies?
I've heard that Evapo-rust is good . Good to the point it will strip bluing to bare steel . They say it deoxydizes the rust ,in theory if it isn't lifted it is restored. It's been spoken of well enough by machinists to make me look for it on the shelves when I'm out .
Just a Red neck,White boy, Blue blood American.....
-
- Posts: 15
- Joined: 27 Dec 2014 11:43
- My Press Choice: Turret
- Location: tn
- Has thanked: 7 times
- Been thanked: 7 times
Re: Tumbling dies?
Thanks for all the info guys. I think I may try removing the rust using some chemical means.