LEE classic turret mods
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
LEE classic turret mods
Hey, forum,
At my last match I found problems with my .38spl ammo. Some cases are just a hair shorter than others, and on these my crimp was not suffitient. I had two rounds teleskoping together in the mag tube of my Winchester 66.
I got about 800 rounds of that ammo left, and I don't want to have that happen again. Decorking them, reuse powder and bullets would be too much of a hassle, so I thought I just put a bit more of a crimp on them. I can't put loaded rounds through my pro1000, so I needed another idea.
Just a few weeks ago I ordered a LEE classic turret, that arrived just in time for this project.
I put an Inline Fabrication reverse indexing rod on it, and the custom made four way case kicker. All I needed now was four identically set seat/crimp dies... or a non indexing turret. So I drilled out the square hole in the bottom of one of my turrets, and voila: a non indexing turret on a reverse indexing shaft with custom case kicker.
Please have a look on my video to see how it works. I didn't show the turret underside, I guess you all know how a hole looks like, and because I only had my mobile phone to capture the video, I couldn't feed cases. But it's obvious how it works.
[youtube][/youtube]
At my last match I found problems with my .38spl ammo. Some cases are just a hair shorter than others, and on these my crimp was not suffitient. I had two rounds teleskoping together in the mag tube of my Winchester 66.
I got about 800 rounds of that ammo left, and I don't want to have that happen again. Decorking them, reuse powder and bullets would be too much of a hassle, so I thought I just put a bit more of a crimp on them. I can't put loaded rounds through my pro1000, so I needed another idea.
Just a few weeks ago I ordered a LEE classic turret, that arrived just in time for this project.
I put an Inline Fabrication reverse indexing rod on it, and the custom made four way case kicker. All I needed now was four identically set seat/crimp dies... or a non indexing turret. So I drilled out the square hole in the bottom of one of my turrets, and voila: a non indexing turret on a reverse indexing shaft with custom case kicker.
Please have a look on my video to see how it works. I didn't show the turret underside, I guess you all know how a hole looks like, and because I only had my mobile phone to capture the video, I couldn't feed cases. But it's obvious how it works.
[youtube][/youtube]
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
-
- Founding Member
- Posts: 736
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: Kingsland, GA
- Has thanked: 51 times
- Been thanked: 222 times
Re: LEE classic turret mods
Interesting modification. I've actually been thinking of doing a one time mass processing of all my pistol brass just to get it all the same length because of the same issue.
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: LEE classic turret mods
All you need is a spare turret, and I used a countersink drill bit OD 16mm to clean out the square hole.
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- buckeye43210
- 250 Shots
- Posts: 253
- Joined: 20 Dec 2014 09:47
- My Press Choice: Progressive
- Location: TPA
- Has thanked: 23 times
- Been thanked: 131 times
Re: LEE classic turret mods
Fyodor, you could have also removed the indexing rod and used the new primer arm case kicker :-)Fyodor wrote:All you need is a spare turret, and I used a countersink drill bit OD 16mm to clean out the square hole.
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: LEE classic turret mods
I could have done... If I already had it printed. I needed to dig out one of the primer arms from my collection to get the bottom part, because the sample was lost my the mail service. I guess I could have the first try made by mid of September. If that works, I'll have a few made and sent back. ![Wink ;)](./images/smilies/icon_e_wink.gif)
![Wink ;)](./images/smilies/icon_e_wink.gif)
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- buckeye43210
- 250 Shots
- Posts: 253
- Joined: 20 Dec 2014 09:47
- My Press Choice: Progressive
- Location: TPA
- Has thanked: 23 times
- Been thanked: 131 times
Re: LEE classic turret mods
Thanks, I know another reloader here in Ohio with a 3D printer. If the files are compatible, he says he can print some for me closer to home.Fyodor wrote:I could have done... If I already had it printed. I needed to dig out one of the primer arms from my collection to get the bottom part, because the sample was lost my the mail service. I guess I could have the first try made by mid of September. If that works, I'll have a few made and sent back.
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: LEE classic turret mods
Update, including pictures and new video (old one's gone):
This is the mod to the turret itself: The setup... just on the bottom left edge of the pic you see a second acro bin left to the other one. I put the untreated cases there, ready to be picked up, and the machine will fill the right bin with the finished cases by itself. The reverse index rod came with a clamp-on chute for the bin, but when you put the bin on the far right, so it touches the press body, you don't need it. I only dropped two cases during my last session, and they flew over both bins
then I slowed down a bit.
Close-up of the Inline Fabrication reverse indexing rod and custom 4-way case kicker. Note the orientation of the shellholder. I tried it in a more comfortable forward angle, but that didn't work well.
And now for some action:
[BBvideo 560,340][/BBvideo]
This is the mod to the turret itself: The setup... just on the bottom left edge of the pic you see a second acro bin left to the other one. I put the untreated cases there, ready to be picked up, and the machine will fill the right bin with the finished cases by itself. The reverse index rod came with a clamp-on chute for the bin, but when you put the bin on the far right, so it touches the press body, you don't need it. I only dropped two cases during my last session, and they flew over both bins
![Rolling Eyes :roll:](./images/smilies/icon_rolleyes.gif)
[BBvideo 560,340][/BBvideo]
You do not have the required permissions to view the files attached to this post.
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
-
- Founding Member
- Posts: 1617
- Joined: 17 Oct 2013 18:09
- My Press Choice: Turret
- Location: West Virginia
- Has thanked: 1017 times
- Been thanked: 323 times
Re: LEE classic turret mods
That kicks the case out pretty good so you don't need a chute at all.
Je suis Charlie