Hello from the Show Me State!
-
- Posts: 10
- Joined: 03 Apr 2016 06:48
- My Press Choice: Progressive
- Location: USA
Hello from the Show Me State!
Hello forum!
Really excited to be here =)
I just ordered a Pro 1000 9mm and am pretty excited/nervous about setting it up, getting correct powder loads...basically everything.
I don't really have any experience, but I have reloaded 12 gauge on a MEC progressive and enjoyed it.
Since ordering from Cabelas, I have read several posts saying that newbies should start out with a single or turret press at most.......sooooooo I'm kind of kicking myself for buying the Pro 1000. (Cabelas was having a sale tho!!!).
Anyway, I haven't got the press yet, I have bought HP-38, Hornaday 9mm .355" 115gr FMJ RN #35557, Remington #1 1/2 and picked up about 300 brass cases. Man, the bullets were crazy expensive, $20 for 100...I'll be ordering those online from now on...Starline has a facility nearby, maybe I'll run in there too.
Really excited to be here =)
I just ordered a Pro 1000 9mm and am pretty excited/nervous about setting it up, getting correct powder loads...basically everything.
I don't really have any experience, but I have reloaded 12 gauge on a MEC progressive and enjoyed it.
Since ordering from Cabelas, I have read several posts saying that newbies should start out with a single or turret press at most.......sooooooo I'm kind of kicking myself for buying the Pro 1000. (Cabelas was having a sale tho!!!).
Anyway, I haven't got the press yet, I have bought HP-38, Hornaday 9mm .355" 115gr FMJ RN #35557, Remington #1 1/2 and picked up about 300 brass cases. Man, the bullets were crazy expensive, $20 for 100...I'll be ordering those online from now on...Starline has a facility nearby, maybe I'll run in there too.
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: Hello from the Show Me State!
Herzlich willkommen from Germany!
My first press was a LEE hand press, which I used for a short time until I graduated to the pro1000 as well.
The pro1000 is not too difficult to master, even for a new reloader. Keep it clean, especially the primer mechanism (including the primer chute) and below the shell plate, use only a little lube, and go as slow as you need to oversee what's happening. Start slow, find a workflow that suits you, but don't try to start mass production at the beginning. Then it's a nice press to learn.
A few tips:
- When I stated "start slow" above, I didn't mean the stroke, I meant the frequency. Your stroke should be smooth and consistent in speed, but take your time in between the up- and down strokes. Consistent ram velocity will give better powder consistency and will prevent jamming
- Check the shellplate nut regularly. If the press doesn't index correctly, most of the time the nut was loose, and the indexing rod turned backwards during the upstroke. That will not only result in wrong indexing (which is easy to recognize), but it will also loosening your shellplate, causing problems with feeding new cases and seating primers. Don't overtighten the nut, but keep an eye on it. A sharpie mark over the edge of shellplate and nut will easily show when it started turning.
- Always have the shellplate full while loading and even for setup. The forces in the press and pressure on the shellplate are different when you cycle only one case, giving inconsistent bullet seating and crimping. When loading for precision shooting, put the first and last two round of a loadin session to the traing ammo pile. If youren't a sharp shooter, it doesn't matter, but still you should know that this does have an effect on the bullet.
My first press was a LEE hand press, which I used for a short time until I graduated to the pro1000 as well.
The pro1000 is not too difficult to master, even for a new reloader. Keep it clean, especially the primer mechanism (including the primer chute) and below the shell plate, use only a little lube, and go as slow as you need to oversee what's happening. Start slow, find a workflow that suits you, but don't try to start mass production at the beginning. Then it's a nice press to learn.
A few tips:
- When I stated "start slow" above, I didn't mean the stroke, I meant the frequency. Your stroke should be smooth and consistent in speed, but take your time in between the up- and down strokes. Consistent ram velocity will give better powder consistency and will prevent jamming
- Check the shellplate nut regularly. If the press doesn't index correctly, most of the time the nut was loose, and the indexing rod turned backwards during the upstroke. That will not only result in wrong indexing (which is easy to recognize), but it will also loosening your shellplate, causing problems with feeding new cases and seating primers. Don't overtighten the nut, but keep an eye on it. A sharpie mark over the edge of shellplate and nut will easily show when it started turning.
- Always have the shellplate full while loading and even for setup. The forces in the press and pressure on the shellplate are different when you cycle only one case, giving inconsistent bullet seating and crimping. When loading for precision shooting, put the first and last two round of a loadin session to the traing ammo pile. If youren't a sharp shooter, it doesn't matter, but still you should know that this does have an effect on the bullet.
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: Hello from the Show Me State!
Welcome to the forum. I don't think you will have a problem with the press or the introduction to reloading metallic cartridges. Just ask questions rather than guess. That will save pulling a lot of ammo plus as you noted, components have gotten expensive.
We have seen a number of first time loader user with the Pro 1000 and I would say that Fyodor is one of our resident expert users so you are in good hands.
We have seen a number of first time loader user with the Pro 1000 and I would say that Fyodor is one of our resident expert users so you are in good hands.
Michael
- Poppop
- 250 Shots
- Posts: 262
- Joined: 02 Mar 2014 16:15
- My Press Choice: Turret
- Location: Easton, PA
- Has thanked: 82 times
- Been thanked: 53 times
Re: Hello from the Show Me State!
Hi
Welcome to the forum.
Enjoy you reloading.
Look for a local dealer that carries FRONTIER Bullets. I pay $95.00 for 1,000. They are made in So. Africa.
http://www.frontierbullets.co.za yes that is the website address
They are 9mm CMJ Round Nose they come in different weights and calibers. Great for plinking and target.
Welcome to the forum.
Enjoy you reloading.
Look for a local dealer that carries FRONTIER Bullets. I pay $95.00 for 1,000. They are made in So. Africa.
http://www.frontierbullets.co.za yes that is the website address
They are 9mm CMJ Round Nose they come in different weights and calibers. Great for plinking and target.
If all else fails--look for the obvious
MAGA
MAGA
- Old Scribe
- Supporter
- Posts: 369
- Joined: 02 May 2015 09:13
- My Press Choice: Turret
- Location: State of Jefferson
- Has thanked: 461 times
- Been thanked: 120 times
Re: Hello from the Show Me State!
Welcome aboard from the State of Jefferson.
"Well here's another nice mess you've gotten me into." Oliver Hardy
- RBHarter
- Founding Member
- Posts: 2046
- Joined: 13 Mar 2014 19:45
- My Press Choice: Single Stage
- Location: The green hell 90 miles north of Texarka
- Has thanked: 76 times
- Been thanked: 672 times
Re: Hello from the Show Me State!
Welcome from the silver state.
Xtreme bullets is just north of me and delivers both cast and plated . Last I looked at their price they were about $80/1000 cast and $105 plated .
Odds are good there is a bullet manufacturer close to you . And then it hits me like a truck ...... Missouri cast bullets might be in your backyard.
Xtreme bullets is just north of me and delivers both cast and plated . Last I looked at their price they were about $80/1000 cast and $105 plated .
Odds are good there is a bullet manufacturer close to you . And then it hits me like a truck ...... Missouri cast bullets might be in your backyard.
Just a Red neck,White boy, Blue blood American.....
-
- Founding Member
- Posts: 1617
- Joined: 17 Oct 2013 18:09
- My Press Choice: Turret
- Location: West Virginia
- Has thanked: 1017 times
- Been thanked: 323 times
-
- Posts: 10
- Joined: 03 Apr 2016 06:48
- My Press Choice: Progressive
- Location: USA
Re: Hello from the Show Me State!
RBHarter, Missouri Cast Bullets is just over an hour away! I'll definitely order from them!!!! Thanks for the heads up!!!