annealing questions from a novice
- akuser47
- Moderator & Supporter
- Posts: 1397
- Joined: 30 Jun 2013 09:16
- My Press Choice: Single Stage
- Location: ohio
- Has thanked: 666 times
- Been thanked: 266 times
Re: annealing questions from a novice
I was gonna look it up and copy and paste that link haven't had the time yet. I love that setup its anppealing
-
- Founding Member
- Posts: 1617
- Joined: 17 Oct 2013 18:09
- My Press Choice: Turret
- Location: West Virginia
- Has thanked: 1017 times
- Been thanked: 323 times
Re: annealing questions from a novice
The only thing I see that could be made better is the case hight adjustment other than that it looks very slick.
Je suis Charlie
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: annealing questions from a novice
It is very easy. The arms are on threaded stock and rotate; clockwise to decrease height and... Literally takes seconds.62chevy wrote:The only thing I see that could be made better is the case hight adjustment other than that it looks very slick.
I leave the flame adjustments alone, the knobs & valves are marked so that I can tell if they have been tinkered with. Just turn the gas on at the bottle and the flames are where they should be. There is really little need to adjust the timing of the anneal either. I have the speed control marked as well. I do check three Templaq'd cases frequently though. Funny thing about that product, you just hang on to the cases with the paint dots. Apparently it stays good. So like when I get ready to run 300 Savage cases I can send the same three plaq'd cases at the front of the run and the check is good. No need to paint new dots, I keep them in a bin at the annealer.
Michael
- alphalimafoxtrot
- Supporter
- Posts: 160
- Joined: 14 Feb 2016 07:19
- My Press Choice: Lee Loader
- Location: Alexandria, Virginia
- Has thanked: 462 times
- Been thanked: 80 times
Re: annealing questions from a novice
RD, that setup is COOL.
When I grows up* and lives in a house with a place to call my own man-cave, that annealer would live there!
take care
Adam
*just turned 52 yesterday FWIW
When I grows up* and lives in a house with a place to call my own man-cave, that annealer would live there!
take care
Adam
*just turned 52 yesterday FWIW
I am a regular joe, consisting of 78% coffee, 12% hot air, 9% organizational abilities, and 1% luck.
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: annealing questions from a novice
Happy birthday! It's never too late for a new set of tools.
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: annealing questions from a novice
I spent the money on the annealer because of the volume I reload, wouldn't not think it this year, but also how hard it is to find a lot of the brass that I'm reloading. I've acquired a lifetime supply based on my needs and I want to ensure it is going to last.
Based on the OPs Lee Loader pace, I think a propane torch with the brass spun on a drill, via the Lee case trimming tools, and then quenching the case in a container of water would be grand. If the torches flame and distance of the case to the torch (2½") where the same, I suspect the same time interval that I'm using under the flame would provide the same results (not over anneal the case). I will see how many seconds my case sits in place in just a bit.
Based on the OPs Lee Loader pace, I think a propane torch with the brass spun on a drill, via the Lee case trimming tools, and then quenching the case in a container of water would be grand. If the torches flame and distance of the case to the torch (2½") where the same, I suspect the same time interval that I'm using under the flame would provide the same results (not over anneal the case). I will see how many seconds my case sits in place in just a bit.
Michael
-
- Founding Member
- Posts: 1617
- Joined: 17 Oct 2013 18:09
- My Press Choice: Turret
- Location: West Virginia
- Has thanked: 1017 times
- Been thanked: 323 times
Re: annealing questions from a novice
LOL Happy birthday, lolalphalimafoxtrot wrote: *just turned 52 yesterday FWIW
Je suis Charlie
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: annealing questions from a novice
Here you go! Belated birthday present!
[BBvideo 560,340][/BBvideo]
Case annealing using a propane torch and Lee trimmer stud on a cordless drill.
The setup uses a wire 2½" wire so that the cases, one to the next, maintain a consistent distance from the torch nozzle for a consistent heat across individual cases. Spinning the case with the Lee Case Trimmer stud allows for an even heating of the neck on all sides.
A four second burn with the case 2½" from the nozzle melts the 750° templaque just inside the case neck, you will see the paint flare up, but not melt the 350° templaque at the base of the above the case's web.
The video is a real redneck unscripted setup with a set of pliers in a vise holding my phone, I apologize for the that but I wanted to post this for a fellow to show how to achieve consistent, case to case, annealing with as little setup as possible. Using the simple wire guide, adjust the flame as I described and also use the wire to keep the case at a consistent distance from the nozzle.
[BBvideo 560,340][/BBvideo]
Case annealing using a propane torch and Lee trimmer stud on a cordless drill.
The setup uses a wire 2½" wire so that the cases, one to the next, maintain a consistent distance from the torch nozzle for a consistent heat across individual cases. Spinning the case with the Lee Case Trimmer stud allows for an even heating of the neck on all sides.
A four second burn with the case 2½" from the nozzle melts the 750° templaque just inside the case neck, you will see the paint flare up, but not melt the 350° templaque at the base of the above the case's web.
The video is a real redneck unscripted setup with a set of pliers in a vise holding my phone, I apologize for the that but I wanted to post this for a fellow to show how to achieve consistent, case to case, annealing with as little setup as possible. Using the simple wire guide, adjust the flame as I described and also use the wire to keep the case at a consistent distance from the nozzle.
Last edited by Ranch Dog on 14 Sep 2018 06:33, edited 2 times in total.
Reason: Added Youtube Notes
Reason: Added Youtube Notes
Michael
-
- Founding Member
- Posts: 1617
- Joined: 17 Oct 2013 18:09
- My Press Choice: Turret
- Location: West Virginia
- Has thanked: 1017 times
- Been thanked: 323 times
Re: annealing questions from a novice
Thanks RD never thought about the 4 seconds or the 2.5 inches I just looked for the change in color.
Je suis Charlie