bent rounds .38spl
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
bent rounds .38spl
Hey, guys,
For my pro1000 I got 4 turrets set up, two of which are .38spl loads. One is dedicated to my blackpowder load, while the other one is used for my smokeless load. Even if the OAL on both loads is identical, that way I avoid the source of error to forget to switch the powder disks.
Not to my problem:
Earlier this year, I had two rounds telescoping in the magazine tube of my lever gun. I was able to extract it and reload on the clock, but it does cost a lot of time. After the match, I closely checked the delinquents and a few unfired rounds and found, that the crimp was a bit light. Actually you didn't even find evidence the case mouth has ever seen a crimp die from the inside. Some cases, which are a hair shorter than the rest, even still showed some light flare.
The obvious solution was to set the crimp a bit stronger, and recrimp all 800 rounds that were left from that batch. I did that on my hand press without any problems. I then replicated the same crimp on my pro1000 smokeless setup. But now I experience some "bent" rounds every so often. There still is no super heavy crimp, but still some rounds are bent. I try to add a picture later today when I got good lighting, it wasn't visible on the first try.
The strange thing is, that the crimp on the blackpowder loads is way stronger, and they never showed such bending. My first thought was a bent shellplate carrier, but since I use the same one for both turrets, that doesn't seem to be the case.
Has anybody ever heard of slanting dies?
For my pro1000 I got 4 turrets set up, two of which are .38spl loads. One is dedicated to my blackpowder load, while the other one is used for my smokeless load. Even if the OAL on both loads is identical, that way I avoid the source of error to forget to switch the powder disks.
Not to my problem:
Earlier this year, I had two rounds telescoping in the magazine tube of my lever gun. I was able to extract it and reload on the clock, but it does cost a lot of time. After the match, I closely checked the delinquents and a few unfired rounds and found, that the crimp was a bit light. Actually you didn't even find evidence the case mouth has ever seen a crimp die from the inside. Some cases, which are a hair shorter than the rest, even still showed some light flare.
The obvious solution was to set the crimp a bit stronger, and recrimp all 800 rounds that were left from that batch. I did that on my hand press without any problems. I then replicated the same crimp on my pro1000 smokeless setup. But now I experience some "bent" rounds every so often. There still is no super heavy crimp, but still some rounds are bent. I try to add a picture later today when I got good lighting, it wasn't visible on the first try.
The strange thing is, that the crimp on the blackpowder loads is way stronger, and they never showed such bending. My first thought was a bent shellplate carrier, but since I use the same one for both turrets, that doesn't seem to be the case.
Has anybody ever heard of slanting dies?
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: bent rounds .38spl
No, I haven't. So, if the shell plate isn't the culprit what about the turret?Fyodor wrote:Has anybody ever heard of slanting dies?
What die are you using for the crimp? Do you trim the brass to a uniform length or at least cull those that exceed the spec length of 1.155"?
Michael
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: bent rounds .38spl
I also suspected the turret, but I got some spares and swapped all dies to a new turret without any effect.
I don't trim or even measure my .38spl brass... it's usually range brass, mixed makes and batches, and I got about 7500 of them... so it's nothing I even want to think about doing. Actually I do have a LEE QuickTrim deluxe for that cartridge, but then it's 7point5thousand of them
What keeps me wondering is that this problem doesn't occur on the other die set.
I don't trim or even measure my .38spl brass... it's usually range brass, mixed makes and batches, and I got about 7500 of them... so it's nothing I even want to think about doing. Actually I do have a LEE QuickTrim deluxe for that cartridge, but then it's 7point5thousand of them
What keeps me wondering is that this problem doesn't occur on the other die set.
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: bent rounds .38spl
True but it might be the odd ball that has gotten too long. The case would be hard to measure if it's bent but maybe it is long and the these cases have just ended up on this press. You might just sample the brass.Fyodor wrote:What keeps me wondering is that this problem doesn't occur on the other die set.
Michael
-
- Posts: 156
- Joined: 12 Apr 2016 13:13
- My Press Choice: Progressive
- Location: SE Michigan
- Has thanked: 32 times
- Been thanked: 38 times
Re: bent rounds .38spl
Regardless whether you are crimping using the bullet sitting die or factory size die, both of them depend on case length.
In the bullet sitting die, to set it up, you first unscrew the die, insert case, raise the case\plate to top position and them screw the die in till it touches the top of the case. Then you adjust for crimp by adding 1/2 to 1 turn of the die clockwise (with case lowered).
Now, if you've performed the setup with a shorter case, and you happen to insert longer case, two things will happen:
1. The bullet will get seated deeper (same Over All Length) and, depending on bullet, the top of case may be sitting above the crimp groove of your bullet making the downwards force higher (as the die has to press harder to crimp into the bullet). This may cause the case to warp/bulge.
2. The crimp will be much larger/deeper as there is more material that needs to be crimped.
Half turn of the die is 0.055" and range from no crimp to "deep crimp", if I interpreted Lee's manual correctly, is 1 full turn which is 0.110". So, if your cases vary up to 0.110" then you will see difference of no to full crimp and possible crushing\warping of cases.
Also, did you change the bullets to something different? Is the top of case aligned with a groove in the bullet?
I'm gonna theorize here on case length...
I presume that you are using powder loads on the higher side of the scale... just a speculation here. Consider this:
A case is a bit longer than others... it gets deeper crimp due to it's length, that would cause pressure to build up more than in cases with less crimp... that would elongate the case upon firing more than cases with smaller crimp... and upon next reload the scenario continues making the case getting longer faster than the other cases.
In the bullet sitting die, to set it up, you first unscrew the die, insert case, raise the case\plate to top position and them screw the die in till it touches the top of the case. Then you adjust for crimp by adding 1/2 to 1 turn of the die clockwise (with case lowered).
Now, if you've performed the setup with a shorter case, and you happen to insert longer case, two things will happen:
1. The bullet will get seated deeper (same Over All Length) and, depending on bullet, the top of case may be sitting above the crimp groove of your bullet making the downwards force higher (as the die has to press harder to crimp into the bullet). This may cause the case to warp/bulge.
2. The crimp will be much larger/deeper as there is more material that needs to be crimped.
Half turn of the die is 0.055" and range from no crimp to "deep crimp", if I interpreted Lee's manual correctly, is 1 full turn which is 0.110". So, if your cases vary up to 0.110" then you will see difference of no to full crimp and possible crushing\warping of cases.
Also, did you change the bullets to something different? Is the top of case aligned with a groove in the bullet?
I'm gonna theorize here on case length...
I presume that you are using powder loads on the higher side of the scale... just a speculation here. Consider this:
A case is a bit longer than others... it gets deeper crimp due to it's length, that would cause pressure to build up more than in cases with less crimp... that would elongate the case upon firing more than cases with smaller crimp... and upon next reload the scenario continues making the case getting longer faster than the other cases.
Last edited by jloader on 11 Jul 2016 09:33, edited 1 time in total.
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: bent rounds .38spl
Unfortunately my bullets don't have a crimp groove. They do have a grease groove (which is empty, because they are MoS lubed), but that's way far too low to repurpose as a crimp groove.
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
-
- Posts: 156
- Joined: 12 Apr 2016 13:13
- My Press Choice: Progressive
- Location: SE Michigan
- Has thanked: 32 times
- Been thanked: 38 times
Re: bent rounds .38spl
I've just added 2 paragraphs to my previous post about case length when you posted your reply...
-
- Founding Member & Supporter
- Posts: 674
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: S. Oregun
- Has thanked: 203 times
- Been thanked: 371 times
Re: bent rounds .38spl
No crimp groove? Are you taper crimping? Perhaps the simple solution would be to use a proper bullet, designed for use in a 38 Special revolver/levergun?
-
- Supporter
- Posts: 888
- Joined: 06 Mar 2016 16:09
- My Press Choice: Hand Press
- Location: SW Ohio
- Has thanked: 156 times
- Been thanked: 240 times
Re: bent rounds .38spl
Oh, I don't know, seems to me the "proper"bullet for a levergun or any gun for that mater is the one that cycles and shoots best regardless of it design. I will grant that roll crimping without a crimp groove can be problematic for accuracy, but not always and mostly with jacketed bullets.
I'm assuming since he speaks of loading 800 rounds that he is more than satisfied with the load. So a suggestion or two look for and either trim or cull the long cases, get on of Lee's special run collet crimp dies or switch to taper crimping. You could of course live with occasional bent case as a culling program, but none of would go for that.
Make smoke,
I'm assuming since he speaks of loading 800 rounds that he is more than satisfied with the load. So a suggestion or two look for and either trim or cull the long cases, get on of Lee's special run collet crimp dies or switch to taper crimping. You could of course live with occasional bent case as a culling program, but none of would go for that.
Make smoke,
Curt.......makin' smoke and raising my carbon foot print one cartridge at a time
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: bent rounds .38spl
Thanks for your replies up to now, I'm learning a bit from every single one, keep going!
My load is a Cowboy Action load, so my priorities are, in that order:
I also never heard about straight cases to elongate under pressure.
This is how the cases look like: You can see, that I don't apply a heavy crimp, it's still barely visible.
I once tried to seat the bullet a bit deeper, and crimp over the shoulder of the bullet. That didn't work well, even when the case mouth wasn't presses into the lead, the cases bulged out, and I had to apply an insane crimp to have them feed in the lever rifle.
My load is a Cowboy Action load, so my priorities are, in that order:
- 100% ignition on first strike
- smooth feeding in the lever gun
- precision
I also never heard about straight cases to elongate under pressure.
This is how the cases look like: You can see, that I don't apply a heavy crimp, it's still barely visible.
I once tried to seat the bullet a bit deeper, and crimp over the shoulder of the bullet. That didn't work well, even when the case mouth wasn't presses into the lead, the cases bulged out, and I had to apply an insane crimp to have them feed in the lever rifle.
You do not have the required permissions to view the files attached to this post.
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.