So far I' haven't figured out how, if indeed it's possible, to add a photo plus comments as a reply to a post or not.
With a lot of experimenting with moulds, stem TC's, PIDS and a VOM. all of the few moulds I have responded well to a mould temperature of about 430° F. So present method is I don't use the little shelves I added to the pots years back as my recollection was I never more than 358° readings on of the shelf itself. I run the hotplate at 440°and can rest the mould for a break and it'll still be right where I want it when I get back.
Pots are set at 365° C and the feeder on at 366° and cast pot doesn't drop any while refilling it.
FWIW (probably not much!)
Guess another topic won't hurt anything though.Mould Temperature #2
- MikeW1
- Posts: 19
- Joined: 18 Aug 2023 20:12
- My Press Choice: Progressive
- Location: Rural Sumner,Iowa
- Been thanked: 4 times
Mould Temperature #2
You do not have the required permissions to view the files attached to this post.
There are two ways to conquer and enslave a nation.
One is by the sword. The other is by debt.”
John Adams 1826
One is by the sword. The other is by debt.”
John Adams 1826
- farmerjim
- Supporter
- Posts: 315
- Joined: 29 Jan 2015 14:27
- My Press Choice: Turret
- Location: Saint Francisville LA
- Has thanked: 20 times
- Been thanked: 114 times
Re: Mould Temperature #2
I also use a hotplate to preheat my molds. I also use it to preheat my lead ingots before adding them to the pot.
- GasGuzzler
- Moderator & Supporter
- Posts: 2045
- Joined: 26 Jan 2016 22:39
- My Press Choice: Turret
- Location: Cooke County, TX
- Has thanked: 330 times
- Been thanked: 501 times
Re: Mould Temperature #2
I tried the over-engineered, super complex route and it didn't suit me. Went back to basics and made better bullets.
__________________________________________________________________________________________
I've always been crazy but it's kept me from goin' insane.
I've always been crazy but it's kept me from goin' insane.
-
- Founding Member & Supporter
- Posts: 1123
- Joined: 20 Dec 2013 11:09
- My Press Choice: Single Stage
- Location: Arizona
- Location: Arizona
- Has thanked: 688 times
- Been thanked: 327 times
Re: Mould Temperature #2
Yup, same for me. Back to basics except for my PID. I sure do like the melt stayingGasGuzzler wrote: ↑31 Aug 2023 04:31 I tried the over-engineered, super complex route and it didn't suit me. Went back to basics and made better bullets.
at the same temp all the way down without constantly fussing with the pot's temp control.
A day late & A dollar short? Story of my life ![Shoot'em Up +guns](./images/smilies/icon_guntootsmiley.gif)
![Shoot'em Up +guns](./images/smilies/icon_guntootsmiley.gif)
-
- Supporter
- Posts: 1003
- Joined: 09 Nov 2015 06:35
- My Press Choice: Single Stage
- Location: Washington State
- Has thanked: 38 times
- Been thanked: 274 times
Re: Mould Temperature #2
An older thread but what the heck nothing else seems to be goin' on. Have to admit, haven't cast a bullet in a couple years but I used to do quite a lot. Most was wheel weight alloy and I ran my pot and moulds hot. Kept the melt between 700 and 725 degrees, ran the moulds hot as well. I went as fast as I could pour, drop, and refill the mould. Also never dropped sprues back into the melt. I kept a small dish with water and a damp wash cloth in the dish. Whenever the sprue's starting feeling a bit to "easy" I'd place the mold on the cloth for a few seconds to cool. Run a big sprue, and I mean big, sometimes (usually) the sprue would run the length of the mould. I made good bullets, and I liked them "frosty" looking. Just my method.