New Quick Trim
-
- Posts: 5
- Joined: 15 Sep 2013 07:23
- My Press Choice: Hand Press
- Location: New York
- akuser47
- Moderator & Supporter
- Posts: 1397
- Joined: 30 Jun 2013 09:16
- My Press Choice: Single Stage
- Location: ohio
- Has thanked: 666 times
- Been thanked: 266 times
Re: New Quick Trim
I have never had an issue with LEE's trimmer and lock stud. I even have some cutom length pilots I had ordered thanks to advice on the rossi forum.
-
- Founding Member
- Posts: 127
- Joined: 30 Jun 2013 10:21
- My Press Choice: Load-All
- Location: AL
- Has thanked: 127 times
- Been thanked: 11 times
Re: New Quick Trim
I bought the quick trim in 8mm and it does 7.7 jap and has been doing large meplats on military full metal jackets after I cut the nose off with a Dremel tool. Trims every thing square
-
- Founding Member
- Posts: 736
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: Kingsland, GA
- Has thanked: 51 times
- Been thanked: 222 times
Re: New Quick Trim
Can I get a pic of the bullets? I've thought of doing that with a tool for the Forster trimmer.Zippidydoodah wrote:I bought the quick trim in 8mm and it does 7.7 jap and has been doing large meplats on military full metal jackets after I cut the nose off with a Dremel tool. Trims every thing square
-
- Founding Member
- Posts: 127
- Joined: 30 Jun 2013 10:21
- My Press Choice: Load-All
- Location: AL
- Has thanked: 127 times
- Been thanked: 11 times
Re: New Quick Trim
[IMG]http://img.tapatalk.com/d/14/01/12/6aqazy6y.jpg[/IMG
1st photo is mil 30-06 and cut same. Meplat is about .175" I loose about 5 grains bullet weight by cutting off the nose. I take a flat file and smooth the nose a little.
The second photo is 30-30 that I had loaded spire pts in. They are about 120 grain and thin jackets.
That is best thing about cutting them off you can see the jacket thickness. Some of the military fmj had really thick jackets and some were very thin. Would affect rate of expansion. I have done a variety of mil bullets from 8mm all the way to 223 on the Lyman universal case trimmer. It is easier and faster than the lee quick trim and pilots in the cutter head. It cuts a ring through the jacket. Then I use a Dremel hand saw to cut thru the lead and saw the tip off. I leave it in the fixture and put a couple of strokes with a flat file to smooth it up. You can't tell it from factory except the nose isn't rounded lead.
I can still use the Lee quick trim on 30-06, 7.7jap, 303 Brit and 8mm to increase meplat DIA.
I had been pulling mil bullets and using hornady, Sierra, Speer and others but this is faster if they are reliable
1st photo is mil 30-06 and cut same. Meplat is about .175" I loose about 5 grains bullet weight by cutting off the nose. I take a flat file and smooth the nose a little.
The second photo is 30-30 that I had loaded spire pts in. They are about 120 grain and thin jackets.
That is best thing about cutting them off you can see the jacket thickness. Some of the military fmj had really thick jackets and some were very thin. Would affect rate of expansion. I have done a variety of mil bullets from 8mm all the way to 223 on the Lyman universal case trimmer. It is easier and faster than the lee quick trim and pilots in the cutter head. It cuts a ring through the jacket. Then I use a Dremel hand saw to cut thru the lead and saw the tip off. I leave it in the fixture and put a couple of strokes with a flat file to smooth it up. You can't tell it from factory except the nose isn't rounded lead.
I can still use the Lee quick trim on 30-06, 7.7jap, 303 Brit and 8mm to increase meplat DIA.
I had been pulling mil bullets and using hornady, Sierra, Speer and others but this is faster if they are reliable
-
- Founding Member
- Posts: 127
- Joined: 30 Jun 2013 10:21
- My Press Choice: Load-All
- Location: AL
- Has thanked: 127 times
- Been thanked: 11 times
Re: New Quick Trim
30-30 bullets I had loaded with 120 grain spire pts (t/c contender). I cut them in the Lyman universal trimmer. You can see jacket thinness when you cut them. The 223 bullets are easy to do and will make an explosive varmint bullet from a fmj .