case length gauge idea
Forum rules
Remember that this forum is not associated with Lee Precision, this is just a customer based discussion of product ideas.
Remember that this forum is not associated with Lee Precision, this is just a customer based discussion of product ideas.
-
- Posts: 34
- Joined: 04 Nov 2018 18:59
- My Press Choice: Turret
- Location: Missouri
- Has thanked: 44 times
- Been thanked: 22 times
case length gauge idea
why doesn't Lee mill a flat spot on the case length gauges for a grip spot when screwing into the cutter so you don't mess up and scar the gauge with pliers.
An avid reloader is one poor sole
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: case length gauge idea
Good idea, have you sent it to them?Dannymcmullen wrote:why doesn't Lee mill a flat spot on the case length gauges for a grip spot when screwing into the cutter so you don't mess up and scar the gauge with pliers.
I use my old Sanders archery "nock" pliers, they work great without marring the gauge's finish.
Michael
- Old Scribe
- Supporter
- Posts: 369
- Joined: 02 May 2015 09:13
- My Press Choice: Turret
- Location: State of Jefferson
- Has thanked: 461 times
- Been thanked: 120 times
Re: case length gauge idea
Good idea. I wrap a piece of thin leather around it. I suppose I could mill a flat on it, but that'd take work.
"Well here's another nice mess you've gotten me into." Oliver Hardy
- Macd
- Supporter
- Posts: 1009
- Joined: 16 Oct 2017 16:12
- My Press Choice: Single Stage
- Location: Far East
- Has thanked: 362 times
- Been thanked: 403 times
Re: case length gauge idea
Use a wood vice. If you squeeze the threaded portion together a small amount it is easy to turn.
- daboone
- Founding Member
- Posts: 1397
- Joined: 30 Nov 2013 21:47
- My Press Choice: Single Stage
- Location: AZ, TX, HI
- Has thanked: 677 times
- Been thanked: 787 times
Re: case length gauge idea
When I use case length gauges they tighten them self up once the cutting starts. Why not use these Pliers. the Tsunoda, PL-150SC-S PLA-iers, Replaceable Resin Jaw Pliers w/built-in-spring..
An ignorant person is one who doesn't know what you have just found out.
When setting a job up for myself it must be Idiot Proof as well, as I am a bigger idiot than most people I know, and I prove it to myself everyday.
When setting a job up for myself it must be Idiot Proof as well, as I am a bigger idiot than most people I know, and I prove it to myself everyday.
-
- Posts: 34
- Joined: 04 Nov 2018 18:59
- My Press Choice: Turret
- Location: Missouri
- Has thanked: 44 times
- Been thanked: 22 times
Re: case length gauge idea
Ranch Dog wrote:Good idea, have you sent it to them?Dannymcmullen wrote:why doesn't Lee mill a flat spot on the case length gauges for a grip spot when screwing into the cutter so you don't mess up and scar the gauge with pliers.
I use my old Sanders archery "nock" pliers, they work great without marring the gauge's finish.
yes RD i did but they just kinda blew me off i don't believe the customer service guy actually knew what i was talking about
An avid reloader is one poor sole
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: case length gauge idea
That's a shame.Dannymcmullen wrote:Ranch Dog wrote:Good idea, have you sent it to them?Dannymcmullen wrote:why doesn't Lee mill a flat spot on the case length gauges for a grip spot when screwing into the cutter so you don't mess up and scar the gauge with pliers.
yes RD i did but they just kinda blew me off i don't believe the customer service guy actually knew what i was talking about
A short 1/4" square flat on the shank would be awsome.
Michael
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: case length gauge idea
Yeah, just the cost of tooling up for it would be tough now. They did increase the size of the shell holder recently (unannounced), to give us a little more diameter for our hands.Macd wrote:Guess extra step would add too much cost for such a low dollar item.
Michael
- daboone
- Founding Member
- Posts: 1397
- Joined: 30 Nov 2013 21:47
- My Press Choice: Single Stage
- Location: AZ, TX, HI
- Has thanked: 677 times
- Been thanked: 787 times
Re: case length gauge idea
While we on the subject of Case Length gauges I'll add my storage solution.
An ignorant person is one who doesn't know what you have just found out.
When setting a job up for myself it must be Idiot Proof as well, as I am a bigger idiot than most people I know, and I prove it to myself everyday.
When setting a job up for myself it must be Idiot Proof as well, as I am a bigger idiot than most people I know, and I prove it to myself everyday.